力科WaveMaster 806Zi-A 示波器

• 品名：力科WaveMast...
• 商品品牌：【美国力科(lecroy)】
• 商品重量：0克
• 上架时间：2015-08-12
• 商品点击数：401

Vertical System
Analog (ProLink Input) Bandwidth @ 50 Ω (-3 dB)	6 GHz (≥10 mV/div)
Analog (ProBus Input) Bandwidth @ 50 Ω (-3 dB)	3.5 GHz (≥10 mV/div)
Analog (ProBus Input) Bandwidth @ 1 MΩ (-3 dB)	500 MHz (typical, ≥2 mV/div)
Rise Time (10¨C90%)	63 ps (test limit, flatness mode)
Rise Time (20¨C80%)	47 ps (flatness mode)
Input Channels	4 (Any combination of ProLink and ProBus inputs)
Bandwidth Limiters	20 MHz, 200 MHz, 1 GHz, 4 GHz
Input Impedance	ProLink Inputs: 50 Ω+/-2% for ≤100 mV/div, 50 Ω+/-3% for >100 mV/div ProBus Inputs: 50 Ω+/-2% or 1 MΩ||16pF, 10 MΩ || 11 pF with supplied Probe
Input Coupling	ProLink Inputs - 50 Ω: DC, GND ProBus Inputs - 1 MΩ: AC, DC, GND; 50 Ω: DC, GND
Maximum Input Voltage	50 Ω (ProLink): ±2 Vmax@≤100mV/div, 5.5Vrms@>100mV/div 50 Ω (ProBus): ±5 Vmax, 3.5 Vrms 1 MΩ (ProBus): 250 V max. (peak AC: < 10 kHz + DC)
Channel-Channel Isolation	DC to 10 GHz: 50 dB (>315:1) 10 to 15 GHz: 46 dB (>200:1) 15 to 20 GHz: 40 dB (>100:1) (For any two ProLink input channels, same or different v/div settings, typical)
Vertical Resolution	8 bits; up to 11 bits with enhanced resolution (ERES)
Sensitivity	50 Ω (ProLink): 2 mV¨C1 V/div, fully variable (2-9.9 mV/div via zoom) 50 Ω (ProBus): 2 mV¨C1 V/div, fully variable; 1 MΩ (ProBus): 2 mV¨C10 V/div, fully variable
DC Vertical Gain Accuracy (Gain Component of DC Accuracy)	+/-1% F.S. (typical), offset at 0V; +/-1.5% F.S. (test limit), offset at 0V
Offset Range	50 Ω (ProLink): ±500 mV @ 2¨C100 mV/div ±4 V @ >100 mV/div -1 V/div 50 Ω (ProBus): ±750 mV @ 2¨C100 mV/div ±4 V @ >100 mV/div -1 V/div 1 MΩ: ±1V @ 2¨C140 mV/div ±10V @ 142mV-1.40V/div
DC Vertical Offset Accuracy	+/-(1.5% of offset setting + 1mV) (test limit)
Horizontal System
Timebases	Internal timebase common to 4 input channels
Time/Division Range	20 ps/div¨C128 s/div (Real-Time Mode: 20 ps/div - 64 s/div; RIS mode: 20 ps/div - 10 ns/div, user selectable at ≤10ns/div; Roll mode: 100 ms/div up to 128 s/div, user selectable at ≥100 ms/div and ≤5 MS/s), depending on memory length
Clock Accuracy	< 1 ppm + (aging of 0.5ppm/yr from last calibration)
Time Interval Accuracy	< 0.06 / SR + (clock accuracy* Reading) (rms)
Jitter Noise Floor	For Acq. Length ≤10¦Ìs: 425 fsrms (TIE, typical) For Acq. Length >10¦Ìs: 475 fsrms (TIE, typical)
Trigger and Interpolator Jitter	<0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
Channel-Channel Deskew Range	±9 x time/div. Setting or 25 ns max. (whichever is larger), each channel
External Timebase Reference (Input)	10 MHz; 50 Ω impedance, applied at the rear input
External Timebase Reference (Output)	10 MHz; 50 Ω impedance, output at the rear
Acquisition System
Single-Shot Sample Rate/Ch	40 GS/s on 4 Ch (80 GS/s on 2 Ch using optional WM8Zi-2X80GS External Interleaving Device)
Random Interleaved Sampling (RIS)	200 GS/s for repetitive signals (20 ps/div to 10 ns/div)
Maximum Trigger Rate	1,000,000 waveforms/second (in Sequence Mode, up to 4 channels)
Intersegment Time	1 ¦Ìs
Memory Options (4 Ch / 2 Ch / 1Ch)	S-32 Option: 32M / 32M / 32M (7,500) M-64 Option: 64M / 64M / 64M (15,000) L-128 Option: 128M / 128M / 128M (15,000) VL-256 Option: 256M / 256M / 256M (15,000) Note: On all memory options, WM8Zi-2X80GS External Interleaving Device permits 80 GS/s on 1 or 2ch with twice the memory)
Standard Memory (4 Ch / 2 Ch / 1Ch) (Number of Segments)	20 M / 20 M / 20M (Memory and Sample Rate can be doubled in 1 or 2 Ch mode with use of WM8Zi-2X80GS External Interleaving Device) (2000)
Acquisition Processing
Averaging	Summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
Enhanced Resolution (ERES)	From 8.5 to 11 bits vertical resolution
Envelope (Extrema)	Envelope, floor, or roof for up to 1 million sweeps
Interpolation	Linear or Sin x/x
Triggering System
Modes	Normal, Auto, Single, and Stop
Sources	Any input channel, Aux, Aux/10, Line, or Fast Edge. Slope and level unique to each source (except line trigger)
Coupling Mode	DC, AC, HFRej, LFRej
Pre-trigger Delay	0¨C100% of memory size (adjustable in 1% increments of 100 ns)
Post-trigger Delay	0¨C10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
Hold-off by Time	From 2 ns up to 20 s or from 1 to 99,999,999 events
Internal Trigger Range	±4.1 div from center
Trigger Sensitivity with Edge Trigger (Ch 1¨C4) ProBus Inputs	2 div @ < 3.5 GHz, 1.5 div @ < 1.75 GHz, 1.0 div @ < 200 MHz, (for DC coupling, ≥ 10 mV/div, 50 Ω )
Trigger Sensitivity with Edge Trigger (Ch 1¨C4) ProLink Inputs	2 div @ < 6 GHz, 1.5 div @ < 3 GHz, 1.0 div @ < 200 MHz, (for DC, AC, LFRej coupling, ≥ 10 mV/div, 50 Ω )
External Trigger Sensitivity, (Edge Trigger)	2 div @ < 1 GHz, 1.5 div @ < 500 MHz, 1.0 div @ < 200 MHz, (for DC coupling)
External Trigger Input Range	Aux (±0.4 V); Aux/10 (±4 V)
Max. Trigger Frequency, SMART Trigger	2.0 GHz @ ≥ 10 mV/div (minimum triggerable width 200 ps)
Basic Triggers
Edge	Triggers when signal meets slope (positive, negative, or either) and level condition.
Window	Triggers when signal exits a window defined by adjustable thresholds
TV-Composite Video	Triggers NTSC or PAL with selectable line and field; HDTV (720p, 1080i, 1080p) with selectable frame rate (50 or 60 Hz) and Line; or CUSTOM with selectable Fields (1-8), Lines (up to 2000), Frame Rates (25, 30, 50, or 60 Hz), Interlacing (1:1, 2:1, 4:1, 8:1), or Synch Pulse Slope (Positive or Negative)
SMART Triggers
State or Edge Qualified	Triggers on any input source only if a defined state or edge occurred on another input source. Holdoff between sources is selectable by time or events.
Qualified First	In Sequence acquisition mode, triggers repeatably on event B only if a defined pattern, state, or edge (event A) is satisfied in the first segment of the acquisition. Holdoff between sources is selectable by time or events.
Dropout	Triggers if signal drops out for longer than selected time between 1 ns and 20 s.
Pattern	Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don¡¯t care. The High and Low level can be selected independently. Triggers at start or end of the pattern.
SMART Triggers with Exclusion Technology
Glitch	Triggers on positive or negative glitches with widths selectable as low as 200ps to 20 s, or on intermittent faults.
Width (Signal or Pattern)	Triggers on positive, negative, or both widths with widths selectable as low as 200ps to 20 s, or on intermittent faults.
Interval (Signal or Pattern)	Triggers on intervals selectable between 1 ns and 20 s.
Timeout (State/Edge Qualified)	Triggers on any source if a given state (or transition edge) has occurred on another source. Delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events.
Runt	Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 1 ns and 20 ns.
Slew Rate	Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 1 ns and 20 ns.
Exclusion Triggering	Trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
Cascade (Sequence) Triggering
Capability	Arm on "A" event, then Trigger on "B" event. Or Arm on "A" event, then Qualify on "B" event, and Trigger on "C" event. Or Arm on ¡°A¡± event, then Qualify on ¡°B¡± then ¡°C¡± event, and Trigger on ¡°D¡± event
Types	A, B, C, or D event: Edge, Glitch, Width, Window, Dropout, Interval, Runt, Slew Rate, or Pattern (analog)
Holdoff	Holdoff between A and B, B and C, C or D, or any is selectable by time or number of events
Reset	Reset between A and B, B and C, C and D, or any combination is selectable in time or number of events
High Speed Serial Protocol Triggering
Data Rates	(Option WM8Zi-HSPT) 100 Mb/s - 2.7 Gb/s, 3.0, 3.125 Gb/s
Pattern Length	80 bits, NRZ or 8b10b
Clock and Data Outputs	400mVp-p (typical) AC coupled
Clock Recovery Jitter	2 ps rms + 0.3% Unit Interval rms for PRBS data patterns with 50% transition density (typical)
Hardware Clock Recovery Loop BW	PLL Loop BW = Fbaud/5500, 100 Mb/s to 2.488 Gb/s (typical)
Low Speed Serial Protocol Triggering (Optional)
Optionally available	I2C, SPI (SPI, SSPI, SIOP), UART-RS232, CAN, LIN, FlexRay, I2S (Audio), MIL-1553
Color Waveform Display
Type	Color 15.3" flat panel TFT-Active Matrix LCD with high resolution touch screen
Resolution	WXGA; 1280 x 768 pixels.
Number of traces	Display a maximum of 8 traces. Simultaneously display channel, zoom, memory and math traces.
Grid Styles	Auto, Single, Dual, Quad, Octal, X-Y, Single+X-Y, Dual+X-Y
Waveform Representation	Sample dots joined, or sample dots only
Processor/CPU
Type	Intel® CoreTM 2 Quad, 3.0 GHz (or better)
Processor Memory	8 GB standard
Operating System	Microsoft Windows® 7 Professional Edition (64-bit)
Real Time Clock	Date and time displayed with waveform in hardcopy files. SNTP support to synchronize to precision internal clocks.
Zoom Expansion Traces
Zoom Expansion Traces	Display up to 4 Zoom and 8 Math/Zoom traces
Interface
Remote Control	Via Windows Automation, or via LeCroy Remote Command Set
Network Communication Standard	VXI-11 or VICP, LXI Class C (v1.2) Compliant
GPIB Port (optional)	Supports IEEE ¨C 488.2
LSIB Port (optional)	Supports PCIe Gen1 x4 protocol with LeCroy supplied API
Ethernet Port	Supports 10/100/1000BaseT Ethernet interface (RJ45 port)
USB Ports	minimum 6 total (incl. 3 front panel) USB 2.0 ports support Windows compatible devices
External Monitor Port	15 pin D-Type WXGA compatible to support customer-supplied external monitor. DVI connector to support LeCroy WPZi-EXTDISP-15 additional touch screen display accessory. Includes support for extended desktop operation with optional LeCroy or other second monitor.
Peripheral Bus	LeCroy LBUS standard
Power Requirements
Voltage	100¨C240 VAC ±10% at 45-66 Hz; 100-120 VAC ±10% at 380-420 Hz; Automatic AC Voltage Selection, Installation Category II
Max. Power Consumption	975 W / 975 VA
Environmental and Safety
Temperature (Operating)	+5 °C to +40 °C including CD-RW/DVD-ROM drive
Temperature (Non-Operating)	¨C20 °C to +60 °C
Humidity (Operating)	5% to 80% relative humidity (non-condensing) up to +31 °C. Upper limit derates to 50% relative humidity (non-condensing) at +40 °C.
Humidity (Non-Operating)	5% to 95% relative humidity (non-condensing) as tested per MIL-PRF-28800F
Altitude (Operating)	Up to 10,000 ft. (3048 m) at or below +25 °C
Altitude (Non-Operating)	Up to 40,000 ft. (12,192 m)
Random Vibration (Operating)	0.5 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Random Vibration (Non-Operating)	2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes
Functional Shock	20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
Physical Dimensions
Dimensions (HWD)	14"H x 18.4"W x 16"D (355 x 467 x 406 mm)
Weight	51.5 lbs. (23.4 kg)
Shipping Weight	70.0 lbs. (31.8 kg)
Certifications
Certifications	CE Compliant, UL and cUL listed; conforms to EN 61326, EN 61010-1, UL 61010-1 2nd edition, and CSA C22.2 No. 61010-1-04
Warranty and Service
Warranty and Service	3-year warranty; calibration recommended annually. Optional service programs include extended warranty, upgrades, and calibration services.

45 GHz 实时带宽

力科再次打破了带宽的瓶颈，采用商用中使用最广泛的锗硅工艺，第二代ASIC设计和第六代DBI技术，在实时示波器性能方面达到了前所未有的高度。

• 45 GHz
• 120 GS/s
• 768 Mpts/Ch 分析存储器

 

20 GHz/4ch 模块

带宽20GHz时，4通道上具有原始的非凡的上升时间，过冲，总的或随机的抖动底噪，以及噪声性能。

力科- - 分析存储器领导者

力科已经找到了无缝化并简便地使用长采集存储器的方法。WaveMaster 8 Zi-A系列专有的X-Stream II结构支持捕获、缩放、测量和分析深达768Mpts的多个波形。Intel® Core™ 2四核处理器(12 GHz有效时钟),高速串行数据总线，Windows 7 64-bit 操作系统以及8GB RAM使得WaveMaster 8 Zi-A的专利架构设计如虎添翼。您会感觉到比其他同类产品的处理速度快10-100倍。

最稳定时基和最低的抖动底噪

异常精准和稳定的时基的结合为最佳抖动测量提供了可能，使得抖动底噪低达到了125fs rms的水平。力科还提供了在全记录长度下的高稳定的测量，简化了低频事件的调试。

摆脱探头的限制

高带宽差分探头(最高 25 GHz)、单端有源探头、电流探头、高压以及混合信号可全部连接至 WaveMaster 8 Zi-A示波器并给您一个总体的系统的图像。WaveMaster 8 Zi-A系列的全部示波器都包括了可选的50 Ohm和1 M Ohm输入功能，并可以配合任意的力科探头--无源或有源的，而不需要外接的适配器或电源。

如何购买

售后服务

用户评论

(共0条评论)

• 暂时还没有任何用户评论

总计 0 个记录，共 1 页。

第一页 上一页 下一页 最末页

用户名：	匿名用户
E-mail：
评价等级：
评论内容：
验证码：